How to mount the cables from the housing (front panel) on the motherboard - video tutorial

When we start configuring a system, we face all sorts of small problems, one of those issues where everyone runs away, is mounting cables from the front panel of the casing on the motherboard, in Romanian, leads those thin with very small plugs, which look like jumpers.
Normally chassis front panel cables leading to the front panel (sometimes at the top of the case), cables are for: USB, power on, reset, microphone and headphones, sometimes we also have eSATA or Firewire separate front panel housing can find and card readers that are installed just like uSB.
The operation does not require special experience, anyone can do this, we just need attention and patience, it is sometimes possible to have need and philips screwdriver (star, cross), anyway I think this tool has anyone in the house.
As you'll see in the tutorial video, audio jack and USB are fairly easy to install, more attention needs to be given front panel's (f_panel), here pins on the motherboard are small and quite crowded.
The most important is to have good visibility on the site in question, a flashlight or a desk lamp will help us a lot, also to those who do the work must be almost perfect if you have trouble seeing a magnifying glass can help.
Jacks are usually significant (hdd_led, pwr_Led, reset_sw, pwr_sw), also on the back of each socket will discover an arrow in the right one pin, one marked with an arrow will always be plus and the other minus, if we know that is the plus and why cable is that not only have to locate where we introduce plug pins. In case you do not have that table on the motherboard, motherboard see manual and there you will find the table's front panel pins and their location.
Also in the tutorial, in the end we showed and how to reset the BIOS (CLR_MOS), we have two options, the first option is shorting pins for clr_mos, and the second is by removing the battery 2-3 seconds, while we pin or short out the battery, power cord must be disconnected from the PC and it must be stopped.
This tutorial is part of a series on mounting components started a few days ago, some of which are the following tutorials:
How to mount a CPU cooler and RAM on the motherboard
How to mount a new source or how to replace old power
Optional for knowledge:
The difference between a good and a poor source, connectors, noise and cold start sources

Continuous series… ..

Remember, if you have suggestions, complaints or additions do not hesitate to write in the comments box, de-also if you met the comments box a user has a problem and you can help him, do not hesitate to do it, the only way we can do this place better, see the comments box!
On the comments box trying to get somewhat on the subject so other visitors can offer a tutorial + comments relevant comments may be extra support for user errors, or desire to learn.
Before asking a question try looking through the comments oldest, most times there already answered your question.
Use more categories at the top of the site and the search engine from the right corner to quickly get to what you are interested, we have over 700 tutorials that cover almost every genre of software, we have realized, I you just have to search for them and watch them.

Instructions for use videotutorial.ro

Search Engine.
If for example you have a problem with Yahoo Messenger, you can enter in our search engine terms like Yahoo, Mess, Messenger, id mess, multimess problem messenger, messenger error, etc., you will see that you will have a choice.

Categories.
If you use category drop-down, they find the bar under Home categories: Office, Graphic-Design, Hardware, Internet, Multimedia, Security, System, Storage, Backup, under these categories are organized sub-categories and sub-sub -categorii, that's a more accurate filtering. To find something related to Yahoo Messenger using the categories you can lead the category:InternetThere will open other subcategories where you choose Voice-ChatFrom there you can go on the subcategory YahooFinally, with these filters will arrive on a page where the only items related to Yahoo Messenger or Yahoo Mail.

Archives.
On the page Archives You can find all our tutorials organized beautiful days saptameni, months and years.
Everything is logical, just follow the logic.

Enjoy !
by Cristian Cismaru



Related Tutorials


About Cristian Cismaru

I like everything related to IT&C, I like to share the experience and information I accumulate every day.
Learn as you learn!

Comments

  1. Thank you very much

  2. Thanks for this tutorial, I accidentally broke mistake these connections to a computer and I did not bring them back, tutorialu solved the problem, thank you!

  3. Very nice tutorial congratulations.
    Cristi I have a request. Tell me please what camera do you use? I needed the camera to focus and so I would be very useful to know already a model.

    Thank you very much.

  4. AdrianGudus said

    Andrew:
    Very nice tutorial congratulations.
    Cristi I have a request. Tell me please what camera do you use? I needed the camera to focus and so I would be very useful to know already a model.

    Thank you very much.

    Finish with questions related to things we use in props! We kindly ask you. Importantly tutorial. If you were a loyal viewer and you'd be looking at tutorials in the last days (in which the used camera to shoot video) and if you read the comments, you would have learned long ago camcorder uses Cristi. There are singuru who asks for it to already answered this question, we will reply to each one the same question just for the convenience of reading your comments.

  5. I have a small observation to make in this tutorial, although I am not a computer scientist or electronics technician, I am just an enthusiast who learns from where he can. As far as I know the plugs for POWER SW and RESET SW can be connected to the motherboard in any way because there is no problem of + or -, but only give continuity to a certain circuit… no matter how you put them when you press the power button or PC reset will react. You have to take into account the + and - at the socket for HDD LED and POWER LED because only direct current flows inside a PC, and the LED will not light up if you change the polarity. Anyway, you are the strongest and thanks to you, I also had what I learn from the secrets of computer science. I look forward to the next tutorial no matter what it is about. I can say that I have a passion for you. If possible, you can also reply to my messages. I left one at the presentation of the TP-LINK router, because I bought the same model presented by you, Cristi, and I have some problems with it and I don't know what I could do to make it work properly. Good luck.

    • Yes so it is power and reset switches are just simple, can be mounted but not bad anyway to use the same logic everywhere, it's so simple.
      My router works perfectly, as well as Adrian, and he has the same model.
      It's probably something wrong with you, besides magnetism router or interference with other devices.
      If the wire goes well, it should work on wireless, wired if it goes wrong means there's a wrong setting made.

  6. Can not wait for more!

    • If you are impatient, you can subscribe to our channel on youtube, there are tutorials posted filmed before a few hours, sometimes even the day before publication on the website.
      YouTube is posted immediately after shooting.

  7. Howdy. I would also like to make a small remark, although I am not a computer scientist or electronics technician, although I would have liked it very much. As far as I know the POWER SW and RESET SW sockets can be connected on the motherboard anyway because there is no + and - as in the case of POWER LED and HDD LED… in the case of LEDs must be taken into account because inside a PC is direct current and alternating current as in the socket. That's about all I have to criticize: p… And now we continue with the praises… you are the strongest and I really appreciate the work you put in here… I think I can say with my heart that I am your biggest fan. I look forward to the next tutorial no matter what it is about. I can say that I made a passion for the work that you submit by doing these tutorials. Good luck

    PS: I wish if I can receive and reply to comment from someone I posted the presentation TP-LINK WR740.

  8. Cristi-admin:
    Yes so it is power and reset switches are just simple, can be mounted but not bad anyway to use the same logic everywhere, it's so simple.
    My router works perfectly, as well as Adrian, and he has the same model.
    It's probably something wrong with you, besides magnetism router or interference with other devices.
    If the wire goes well, it should work on wireless, wired if it goes wrong means there's a wrong setting made.

    Cristi-admin:
    Yes so it is power and reset switches are just simple, can be mounted but not bad anyway to use the same logic everywhere, it's so simple.
    My router works perfectly, as well as Adrian, and he has the same model.
    It's probably something wrong with you, besides magnetism router or interference with other devices.
    If the wire goes well, it should work on wireless, wired if it goes wrong means there's a wrong setting made.

    I apologize because I posted the same thing 2 times but had fallen Addicted and I checked first was not on site ... the router I have no problems with emission wireless ... but I have problems with the data coming into it ... I have internet ip static and have the following data provider ... IP: 94.62.25.59; 255.255.255.224 subnet mask; Default gateway: 94.62.25.1; DNS and Alternate DNS 10.0.0.1: 10.0.0.10 ... the problem is that after placing the data in router and give rescue gives me an error ... "Error code: 5007
    Bad Gateway for WAN IP, please input Another one. "... The only problem that I have ... a friend of mine had a similar problem and solved it with a firmware update but the problem with me is I and the the newest firmware on it ... you think you might be or what I could do in this particular situation? Thank you

    • Talk to your provider may need to clone the Mac.
      Provider is in the best position to tell you the settings you have to do the router.

      • I tend to think it's a software problem as long as the mac is cloned well and it only gives me an error when saving the ip without connecting the internet cable to the router… I would like to update to a custom firmware, namely DD-WRT… do you think it would be a solution?

    • Subnet mask seems strange (possibly because it was not going with all updates made them a)

  9. Cristi-admin:
    Talk to your provider may need to clone the Mac.
    Provider is in the best position to tell you the settings you have to do the router.

    Well, I cloned macu, everything is fine… I don't understand why he doesn't want to save my data… I've had the router for 6 months and it worked perfectly and this month they changed the data and they don't want to be saved in any way bate I'm thinking to try a custom firmware… do you think it could be a solution?

    • First you need to tell us what you provider (RDS, UPC, Romtelecom, net neighborhood), also tell us your settings.
      Custom firmware is not a solution for you.

      • I have a neighborhood net… the settings I have from the provider are:
        - IP: 94.62.25.59
        - Subnet Mask: 255.255.255.224
        - Gateway: 94.62.25.1
        - DNS: 10.0.0.1
        - DNS alternative: 10.0.0.10
        I have no other settings, I even gave it a factory default and in vain… I tried to enter this data with net cable connected to the router and without cable, and via cable from laptop to router and wireless and it always gives me same error… I tried to change the Subnet Mask with 255.255.255.0 and saved the settings but it doesn't work net… I spent a whole day trying solutions. I was thinking that if my friend who had a similar problem on a router from another company and with an update solved it, and I don't have an update, I thought that maybe it would be a DD-WRT solution and I said first to talk to you have experience and knowledge in the field.

      • I don't understand why some of the comments posted don't appear on the site and when I send the second one, the first one appears… strange… I resume for any eventuality…
        I net neighborhood and those from static ip net gave me the following information:
        - IP: 94.62.25.59
        - Subnet Mask: 255.255.255.224
        - Gateway: 94.62.25.1
        - DNS: 10.0.0.1
        - DNS alternative: 10.0.0.10
        Other settings have not since I tried a factory default and nothing, the only solution that worked was to change Subnet Mask with 255.255.255.0 in these conditions saved my settings but this Subnet Mask goes Addicted than at the 224 . Sorry again if it happens to post the 2 times but do not understand why there are no comments nor 15-20 minutes after I posted and occur only after you post on the 2 century.

        • Network card in your PC you put on the car?
          You put your Mac to the network card in your PC to the router?

          • board network ip ... I have distributed and put on laptop and desktop 192.168.1.100 192.168.1.101 and mac router is placed in and saved ...

          • Mirel:
            board network ip ... I have distributed and put on laptop and desktop 192.168.1.100 192.168.1.101 and mac router is placed in and saved ...

            Do you have any idea what it might be? or do you find it strange? normally he should have just saved any numbers you typed in there…

  10. nicu hard said

    Hello, with approx. a year and a half ago, when you were doing the tour with the intel i3 system, I decided to do a calculus too. from scratch, the problem is that in the 'fire' of shopping I was not careful and I bought a case without headphone jacks, the ones that are on the front panel. Can you tell me where I find those jacks, possibly with I can tell you that I only found it with the case or 'sh' [in which case the owner was 500km away. of Buc.]

  11. Excellent, excellent, excellent, God, what useful tutorials are the latest hardware, tineo So Christ, you become a star!

  12. Excellent tutorial. Cristi a small matter, not all cases have that small sign that there is a +, I have a case that does not have that sign and in addition to POWER Led I have three wires, and I always have to change the place of the wires when I change the board, yes it was 2, yes it was 3. For example, on a Fujitsu Simens D1521 board or a Compaq Intel board, the front panel is positioned and the memory slots are lined up there. But in my opinion this tutorial is for beginners, you also have the board book and you don't know, but… .. that's it

  13. AdrianGudus said

    Mirel:
    I apologize because I posted the same thing 2 times but had fallen Addicted and I checked first was not on site ... the router I have no problems with emission wireless ... but I have problems with the data coming into it ... I have internet ip static and have the following data provider ... IP: 94.62.25.59; 255.255.255.224 subnet mask; Default gateway: 94.62.25.1; DNS and Alternate DNS 10.0.0.1: 10.0.0.10 ... the problem is that after placing the data in router and give rescue gives me an error ... "Error code: 5007
    Bad Gateway for WAN IP, please input Another one. "... The only problem that I have ... a friend of mine had a similar problem and solved it with a firmware update but the problem with me is I and the the newest firmware on it ... you think you might be or what I could do in this particular situation? Thank you

    Please go to this video and do what I explained there: http://www.screenr.com/gwB8
    When you make these settings, it must be inserted into the cable net cable from the router and router, inserted into the PC.
    Comments do not appear immediately what you post but only after we check and approve them manually. So, after you give a comment, you must have patience for it to be moderated and approved.

  14. Cristi I can not connect my computer front panel audio jack because I two-wire and some with a single thread and can not connect you can help me somehow? I'm ra primrose comment I grersit

  15. All these tutorials are made by other models in America and other countries and what is new in these tutorials is that they (administrators) are tutorials for installing a PC from A to Z. Bravo to you keep up the good work and more people are look at you and more people learn

  16. vicentiu said

    How can I disable optical audio not to stay lit on the motherboard gigabyte install Windows ep45 ds3l having 7 x64

  17. ilie:
    All these tutorials are made by other models in America or other countries and what is new in these tutorials is that they (the managers) are tutorials for installing a PC A to Z. Bravo to you keep up so many people are look at you and more people learn

    The truth is that Americans have invented the PC, that does not mean we go by them and others made this tutorial we are 100% original creation. Romans do not think we're dumb, and we can do a lot of things, some even better than the Americans, if we do our best course.
    Sure, we invented new operating systems, software or hardware, we teach people how to use it.
    Your comment is at least… weird, I don't know what you meant by the end.
    I repeat.
    We do not copy anyone videotutorial.ro team, our visitors know very well.

  18. I'll say a little "criticism" without upset ok? the video should have been edited with a sony vegas software for some details (zoom, light, etc.) I don't say it with bad intentions at all 'I think that the criticisms and appreciations also have their purpose! A useful and very well explained tutorial, Thank you

  19. AdrianGudus said

    sklipy:
    A saspun myself a little "critical" no offense ok? Video should be edited with software like sony vegas for some detali (zoom, light etc) do not say it maliciously at all 'I think criticisms and assessments have their purpose! A tutorial useful and very well explained, Thanks

    We do not film. We do tutorials on technique, technology. It sees everything as it should? Gets along well sound? The image is synchronized with the sound? Then I do not have any other thing. Not only do the clips adorned sake of art.

  20. AdrianGudus said

    sklipy:
    A saspun myself a little "critical" no offense ok? Video should be edited with software like sony vegas for some detali (zoom, light etc) do not say it maliciously at all 'I think criticisms and assessments have their purpose! A tutorial useful and very well explained, Thanks

    Stop trying to compare us with some others. Unfortunately for some and fortunately for us, we are not the ones who make cartoons in which language to use infantilopornografic.

  21. Mirel:
    Many thanks for your response video ... I did a little video in which I try to explain what it is about ...http://www.youtube.com/watch?v=Tjd-kSVF8U4

    Given how you connect when you put the cable live, do you use an application like "internet starter" or does the net work directly?

    • I don't use any application… .the network is based on poppy and ip… you enter them where you need them and everything works perfectly… now I took it to the service at emag if I still had a road there… thank you very much anyway

  22. sklipy:
    A saspun myself a little "critical" no offense ok? Video should be edited with software like sony vegas for some detali (zoom, light etc) do not say it maliciously at all 'I think criticisms and assessments have their purpose! A tutorial useful and very well explained, Thanks

    All things added in addition, can increase file size, we do not intend to do commercial stuff, we just want to pass the information on, as simple
    The sound is good, the picture is good (have something light, is working on it), otherwise everything is as it should be, pure information.
    If you have complaints about picture quality or sound will listen, but do not ask us to transform tutorials in marketing products, we are not television.

  23. Cristi if it was a asus motherboard, msi or any other besides gigabyte, it was not mounting signs of polarization is inscribed, or to be connected

  24. welcome to watch the 2 years and 5 Access site at least twice a day to see if something new has appeared even watch tutorials and after each of them and put in place about this tutoerial can say it's good but I one between bars near those pins on the motherboard I saw a strength or do not know how his say anyway is small and the color of silver and across it goes a silvery sarmulita all nice sami please say what makes that thing uses thank you so much and you are my website at Maiu favorite of you I learned about 50 percent of what I know

  25. if you can to as many tutorials on hardware and android will esteem smartphonurile are absolutely brilliant

  26. AdrianGudus said

    Mirel:
    Many thanks for your response video ... I did a little video in which I try to explain what it is about ...

    The MAC is cloned! Your router Says Mac PC is different than in the top box.
    When Mac clone, which is in the box below that says Your`s PC and MAC Address must be up.
    Go to the router then the Mac clone and click Clone MAC Address. Both houses must have the same MAC

    • Adrian here I want to contradict you… the bottom poppy should not have to do with the top one… the top one is the one that introduces it to go clean and the bottom one is the computer you use on the router… last night I was on the laptop … If I had connected from the PC the lower mac would have been different from last night because I changed my network card from the PC and I didn't call the provider to announce and I used the net on the poppy of the old network card that burned. I'm a beginner compared to you but that doesn't mean I don't know what to eat some things with… I said it and I repeat it "I USED THE ROUTER FOR 6 MONTHS WITHOUT PROBLEMS AND NOW WHEN THE ONLINE CHANGED THE DATA (ip and gateway ) THE ROUTER NO LONGER SAVES THE SETTINGS… ”I didn't ask here why my internet doesn't work but why it doesn't save my ip and I still tend to believe it's from software so if I still got through crangasi today I took the router to emag for service…. anyway thank you all for trying to help me… all the best…

  27. Far be it from me, Cristi, to ask such a thing, I still have respect for you! I didn't want to sound critical, yes you even said that you can give suggestions and in the text above it is even specified that you can give suggestions, complain… It's not a criticism, I can't afford something like that, it was just a simple suggestion ! Yes you are right the material is more than you can ask for, HQ video quality! Finally, let's talk I really like the site and your way of responding to comments is ok so even the beginning of your tutorials sounds like this: Hello friends, so we are among friends here and that's why I expressed my opinion about the small video adjustments ! Thanks a lot for the answer. Hi I hope it is not a double post! yes I fell net

  28. Cristi-admin:
    I thought I was already a megastar but your comment confirmed my fears, I have to get "only" star
    Wtf ... ..more I pulled ... ..

    :))) come on you were nice 😉 you are a star, but megastar is a stage above, until you reach the news you are just a star 😀 =)) you were strong at this stage…

  29. Listen Cristi, I would like you to tell us something about the following antiviruses in the future when you feel like it: Panda, G-Data, the new versions of bitdefender that I see are very successful lately, even abroad… if you want Tell me how many CVs in a comment, if you tested one of these antiviruses, what do you think, etc., I want that? because I'm thinking of buying a security license (internet secrity), what would you recommend? bitdefender I heard that, it consumes cv memory and makes it difficult for the pc, panda and g-data I lit good houses and it doesn't consume… what do you say? what do you recommend I don't have a lot of money (ie millions). I hope you will answer me. Thank you very much, Star 😉

  30. Cristi Hello! I have a misunderstanding ... I 2 the front panel jacks: one for headphones and one for microphone. Not connected to the motherboard I do not go headphones and microphone? ... Just back I can use. I am waiting for an answer. Thanks!

  31. Very useful this tutorial helped me a lot because I had this problem even PC pins were placed Calum.

  32. Andy:
    Cristi Hello! I have a misunderstanding ... I 2 the front panel jacks: one for headphones and one for microphone. Not connected to the motherboard I do not go headphones and microphone? ... Just back I can use. I am waiting for an answer. Thanks!

    It would be better to rephrase a little, and you try to use commas, to understand us.

  33. AdrianGudus said

    Andy:
    Cristi Hello! I have a misunderstanding ... I 2 the front panel jacks: one for headphones and one for microphone. Not connected to the motherboard I do not go headphones and microphone? ... Just back I can use. I am waiting for an answer. Thanks!

    You can find out for yourself, we have no way of finding out. Open the cover on the unit and see if the wires coming from the front panel are connected to the motherboard. how would you think we could know what you have on your PC? We are not telepaths, I want to let you know!

  34. incognito said

    The tutorial is so ok that even a fool would understand how to mount those cables…
    Good for you!

    PS: Batz sin ala the skewer that has nothing on it :)) :))

  35. marius189 said

    I have a problem to a PC when you turn on the light turns from hdd (red in my case) lit all coolers go but the monitor is blank, video card has been tested and go 100%, I unplugged the HDD plate basic and LED remains lit if you can help me thank you

  36. Very interesting video tutorial. Thank you !
    Am I related to hardware tutorials!

  37. very useful…. bravo are the strongest

  38. marius189:
    I have a problem to a PC when you turn on the light turns from hdd (red in my case) lit all coolers go but the monitor is blank, video card has been tested and go 100%, I unplugged the HDD plate basic and LED remains lit if you can help me thank you

    I also had such a problem last night.

  39. Andy: I also had such a problem last night.

    But after a while he recovered on his own. I don't know what he has or has had…

  40. @cristi front panel and I have no idea but I do not go dc front panel audio and microfonu? usub go. however it's put right inside checked but it just does not work.

  41. Hello Cristi,
    We may meet more cables than the tutorial?
    Thanks for the tutorial.

  42. calin:
    @cristi and front panel I have no idea but I do not go dc front panel audio and microfonu? usub go. however it's put right inside checked but it just does not work.

    @catalin I have the same problem… I don't know what I can do to them

  43. Thank you!

  44. I have one question besides those pins on the motherboard we saw strength or do not know how his say anyway is small and the color of silver and over it goes a sarmulita all the silver that please sami say what makes that thing to what uses thank you so much and you are my website at maiu items from you I learned about 50 percent of what I know

  45. @adrianGudus you're pretty hard to repeat your cranky? those faithful can not really interested in all the tutorials. what's the point urmaesca cnv a helpful tutorial that not now but maybe in the future only or never. 90% here are convinced that only urmaseasc tutorials that interest them. The man asked not only gave head. You can repeat play. no offense. do a good job to be cranky sometimes yes or say no I said once again sucks.

  46. Julian Romica said

    nice tutorial
    Cristi I have a motherboard ASUS P5PE and do not know how to mount USB devices in front (for they have many threads as (2 jacks GND, 2mufe POWER 1 jack D2 + and one D2-; 1 mufaD3 + and one D3-

  47. Very useful. Thanks for the work.

  48. Hi!
    It's very complicated, at least for me… if I didn't move those plugs everywhere and it still doesn't work, my PC won't turn on… I did as you said in the tutorial, except for the part with -p.led and plus p. led, I never found where it says -p.led, where to put them.
    Is there a risk if I put them like this in several ways? for example, if I put HDD LEDD instead of reset sw and so on… can something happen? But of course, I disconnected the PC from the mains, but then after I inserted them I turned on the PC several times in several ways,… as I said above, I reversed them, I tried them on all… close ..
    If you have time, please only respond if there is a possibility of damage in case of moving sockets not everyone where they belong.

  49. those things that catch white wires are called necklaces. so I am working with a company of automotive wiring.

  50. marius said

    hi i just bought a PCI audio card Genius Sound Maker value (put a link do not want to advertise but you can help http://www.emag.ro/placa-de-sunet-genius-5-1-sound-maker-value-pci-3-1720009100/pd/EB1Q3BBBM/ ) And was wondering if I could mount audio front it does not say anywhere that if you can or if you ask me who knows how to say

  51. Basil Dumitrache said

    Hi guys, I'm still trying to find you but in vain I fail… I also have a big problem for me… I have a Fujitsu Siemens motherboard…. ´and it has a front panel… the thing is that I don't know how to mount them where I need them… .. I want 5 caps and they want 25 pins… .. they kill me for days… the plate models are d2156 a11 gs3 and another one d2156 a11 gs6… both with the same front panel

    please help… my id .. dumitrache_vasile18 for who wants to help me

    thank you

  52. George Ghinescu said

    I 7 wires coming out of the front panel audio and motherboard Gigabyte GA-G31M-S2L I 10 (9) pin motherboard manual and do not write
    small-in
    gND
    low-bias
    spkout-r
    r return
    it spkout
    return it

    I do not know how to connect them.
    A help. Thank you!

  53. Hello, I have a question I want to buy a video card http://www.emag.ro/placa-video-gigabyte-nvidia-geforce-gtx-750-ti-oc-windforce-2x-2048mb-gddr5-128bit-2x-hdmi-2x-dvi-n75toc-2gi/pd/DW2H4BBBM/ and I want to give me advice if you behave well or very well on my system: Motherboard Socket Assrock H87 1150, 3 I3.4 GHz Intel processor, Ram and power 4Gb 500W

  54. If defective it may replace the Power button Reset? (That's where the reverse and links on the motherboard).

  55. Power.Il can replace defective button to reset if the reverse connections on the motherboard? .Multumesc.

  56. Hello!
    I want to buy this housing (Floston X-POWER) http://www.emag.ro/carcasa-floston-middle-tower-fara-sursa-negru-x-power/pd/DDGKX2BBM/ and I do not see that has restart button. What to do? I can put them restart button? It is found in the store? I have to cut out housing?
    What would you do?
    Thank you in advance.

  57. titus baroiu said

    Hello !
    I have a Segotep k6 case that has a 2-pin LED SW jack. and button on the LED housing. Where do I connect these pins to the motherboard?
    Self!

Trackbacks

  1. […] You don't know how to mount the front panel, consult the technical book and follow the tutorial: https://videotutorial.ro/cum-se-monteaza-cablurile-de-la-carcasa-front-panel-pe-placa-de-baza-tutoria… I trust you will do well. [...]

  2. […] Be useful, is the one with front panel mounting (USBs and audio jacks on the front of the case): Mounting front panel jacks on the motherboard. Or maybe you want to buy a cheap case and do not know how to mount it: Component mounting […]

Speak Your Mind

*