Hi friends, in this video tutorial will show you install custom firmware DD-WRT on TP-Link TL-WR740Nthis wireless router super cheap (around 80 million) videotutorial.ro was presented in a procurement guide, then I promised I realize tutorial today.
Firmware DD-WRT is one of the most capable firmwares aftermarket, it offers plenty of new features that you do not have version default firmware, DD-WRT can raise the value of a router, in our case lei from 80 300-400 until the lei, not bad at all, let alone where you put the firmware DD-WRT is free.
In this video tutorial we showed How to install DD-WRT ONLY ROUTERULTP-LINK TL-WR740N, IN other routers may be different fewer steps, you should read Section SUPPORT FROM OFFICIAL SITE DD-WRT.
At the end of the tutorial we showed and how it returns to the default firmware TP-Link, all I did in tutorial was made live, I have not experienced any setting, I presented only briefly following menus DD-WRT as ln a tutorial later to continue with settings and other miracles.
Finally you really need to clear something very specific, characters capitalized (that is important):
TUTORIAL procedures listed CAN DAMAGE YOUR ROUTER, lose warranty, or at worst you can lose ROUTER FINALLY, IF YOU HAVE ANY DOUBT OVER refuse such procedures, are not obligated to DO WHAT WE DO, AND SO CAN FOLLOW tutorial.
IF YOU STILL WORK, PLEASE BE CAREFUL, "MEASURE" 2 TIMES AND "CUT" ONCE, YOU WILL NOT HAVE A SECOND CHANCE IF SOMETHING GOES WRONG.
BE CAREFUL !
Remember, if you have suggestions, complaints or additions do not hesitate to write in the comments box, de-also if you met the comments box a user has a problem and you can help him, do not hesitate to do it, the only way we can do this place better, see the comments box!
On the comments box trying to get somewhat on the subject so other visitors can offer a tutorial + comments relevant comments may be extra support for user errors, or desire to learn.
Before asking a question try looking through the comments oldest, most times there already answered your question.
Use more categories at the top of the site and the search engine from the right corner to quickly get to what you are interested, we have over 500 tutorials that cover almost every genre of software, we have realized, I you just have to search for them and watch them.
Instructions for use videotutorial.ro
Search Engine.
If for example you have a problem with Yahoo Messenger, you can enter in our search engine terms like Yahoo, Mess, Messenger, id mess, multimess problem messenger, messenger error, etc., you will see that you will have a choice.
Categories.
If you use category drop-down, they find the bar under Home categories: Office, Graphic-Design, Hardware, Internet, Multimedia, Security, System, Storage, Backup, under these categories are organized sub-categories and sub-sub -categorii, that's a more accurate filtering. To find something related to Yahoo Messenger using the categories you can lead the category:InternetThere will open other subcategories where you choose Voice-ChatFrom there you can go on the subcategory YahooFinally, with these filters will arrive on a page where the only items related to Yahoo Messenger or Yahoo Mail.
Archives.
On the page Archives You can find all our tutorials organized beautiful days saptameni, months and years.
Everything is logical, just follow the logic.
Enjoy !
by Cristian Cismaru
Interesting
the thing that interests me is not to sprouts amount router. The thing that interests me is her speed, or distance from working?
Yagi antennas are used in other types of configurations (they were also used in Ceausescu's time on blocks), some use the word "yagi" to sound familiar, no antenna can be used here (tl-wr740n), unless you unplug the router and reconnect to the wireless network card inside.
It can be used a high gain antenna, I have one and do a good job (unidirectional).
Please stop with this distasteful language, unless you have other vocabulary words in trying to abstain.
pretend, I don't know who the cabbage is, but you better learn to make a "quote". Anyway, your answer didn't work for me, and I don't think it works for anyone.
Do not bother.
respectfully
ps.
from my point of view is very nice tutorial
Speed in any case! it is determined by the provider and not the router or modem. You can limit but in any case you can not enlarge
What value would you like to grow them?
Normall that the distance will be the same signal that is very good after 3 walls.
New functions, graphical display of traffic, VPN etc.
With this money… It certainly leads 100mbps in the chain, as for wireless, 133mbps supports the maximum, but you will have 133mbps / 2, that's the rule. 🙂
This router makes all the money: cheap, cpu quality custom firmware stable.
Cristi, something very dangerous table that I gave it right when I got my router DIR-615 router very, very good iam stopped QoS ptr I limited band was ready, ready sal go back and when I benoclat there mia 10Mbps reassure me out. It's cold and very fast as a Edimax bp6104k who was sitting with a wirless access point separately. Nor do it and how you said you do when you do not have to faramami a router that is if you can not you look dozens of times to see what flash you. I did not stick to do better than dismantle a PC to do this. It would be good to do and made a tutorial how to make a custom rom android mobile genre that I still fail
If we speed internet 100 MB / s, goes a router 150 MB / s?
I right now are on the router and have DD-WRT (Asus RT-N10 +) and works fine but your wireless annoys me that fail to set.
Thanks for the tutorial, astep and other tutorials higher, as is he.
SAL MAR IF INTERESTED VRO newer version Radmin VRUN TUTORIAL FOR HIM OR OTHER chest MOI SMSEXE
Several years ago I had a router and update firmware.Nu we wanted to know what happened and I ran router.Am bought another TP-LINK wr974nd.Functioneaza perfect.Nu use only part of what can faca.SFAT: if you do not want to tamper with the router's software !!!
… Good advice !!! you don't know how, you don't get involved!
Why not walk?
If we read the 3 times, if you inform us if you can and we understand why not bring new features?
It especially like dd-wrt firmware is not a router, it works on a variety of routers.
That saying: first learn to ruin
Hello, nice tutorial! I also have a question that has little to do with "I saw the tutorial" for Opera 11, I saw that there you don't say anything about "new window" is it going to open a new window in Opera? or just "new tab"?
Cristian very interesting! Thank Pt Tutorial
😀
I would like a tutorial to make a progam DJ mixes and record them with the programmed please!
I also have a tp-link tl-wr841nd router I followed all the above steps everything went well when I try to connect via wifi I can't if you can do a TUTORIAL WITH ITS SETTINGS I HAVE INTERNET FROM RDS ……… Thank you! !!
please if you can do a tutorial on how we can limit the band, I have a computer and two laptops when entering sormea wife Addicted I go hard and do not know how to limit their band
In order to do this, your router must have the QOS (quality of service) option. From there you can manually or automatically adjust the bandwidth for each device connected to the router, for different protocols… depending on how advanced the router is. yours
please make a tutorial hg 650b firmware how to install and setup
Cristi, Julian is right in his own language, can
increase the efficiency of reception or transmission by using a directional antenna of the yagi type… don't be bad 🙂
He is right in his own way but things are not so simple, yagi is generally used for exterior and interior are models but those are not efficient enough. Antennas yagi emit enough signal directly, lends itself to the realization of bridges wireless, they are not very good when it comes to cover a space larger long distance, I think the man wants to stay nailed on the line emission yagi antenna.
These are us, we like to talk about things that sound geeky, to look more than we are…. Taller…. More beautiful, we quickly do a google search and we come across the suckers' noses.
To increase the coverage area is much better to use a secondary router repeater station (maybe I'll make a tutorial), a good yagi antenna is more expensive than a router and the results are different (in favor of torque routers).
To eliminate flies is better to use plica, not cannon!
Let's be serious.
Man in general is interested in increasing radius router at no extra cost.
OK tutorial! My congratulations!
I just did mention that the second file "Webflash image" - used only to update or down-data from an earlier version already installed on your router. No need to do 2 flashes. "Special image for initial flashing" was sufficiently original firmware on your router if you ...
Once again congratulations for tutorials ...
For my version (revision) hardware is required 2.1 flash uirea both bin sites, or does not want.
But if not officially supported flash uiesc go amblele bin sites.
Can I ask you what did not work? or he did not want?
Multam`
http://www.dd-wrt.com/wiki/index.php/TP-LINK_TL-WR740N
2.1 is not officially supported, it is necessary for both flash uirea bin.uri first helps you go from the default firmware dd-wrt, dd-wrt second updates last vrsiune.
If you want to do otherwise you go ahead.
Flash is not something interpreter if the developer has left some instructions you need to follow, that if you still want to use the device afterwards.
I must admit that the first bin DD-WRT behave very odd, sometimes after flash I see an interface MSI (old type of msi) and sometimes I appear interface DD-WRT (as in the tutorial), I do not know what's thing probably happens because my version REV 2.1
Those who 3 or 4 version can not flash at all, I'll do some saparturi to see what can be done in this case, the principle is much the same hardware.
SHIP router achieved at international level: on their website only firmware version and 1 2. I've got a router like this one. He eevizia 3. I got on their website the two files I flashuit and now works perfectly. It may take a newer version of Flash: to seek buildurile slayer's brain to tp link v2. Rev. Atheros chipset 3 7241 has 400mhz and 32mb of ram.
Another thing: if you want to use the mixed band wireless n then set NB 40mhz turbo channel 1 6 or 11, and to see the difference. The rest goes perfectly, I used a tape 3mbps the astral and does a great job. Cacheul's his job.
Atheros rules
Cristi, yagi antennas is calculated in detail ... and have no connection with Ceausescu or what you use unidirectional antenna, respect from Piticelului.
Ceausescu's time each block having one national block that deal antenna, many antennas were YAGI type with those we caught Bulgarian Posts.
What fun with Studio X (not about xxx) films were coming from the West, if you were a trendy catch Bulgarians, you were on the rise, just like a tablet or a smartphone today.
YAGI is not a new invention, there are some who think it's something new.
Since there is radio man tried to push as far.
… The idea is that in vain you physically make a yagi antenna, if you don't know how to calculate the dipole and the loop… honestly I'm pretty good, meaning my router emits about 800 meters with a small 30 cm YAGI antenna… I mean I can drink a beer with the laptop next to me on the nearest terrace :))))))))))))
Regarding calculations, you are absolutely right, but remember that you are working in 2,5GHz band (and a few tens of milliwatts of power), all calculations can not really miss. You should prnytu equipment adaptations. The best thing is omnidirectional with a gain larger, factory made. To increase the transmission power the router from the few tens of milliwatts milivati over 200, see comment below on the router Link-Sys WRT54GL
Very good tutorial. I managed to flashuiesc a D-Link DIR-300 B1 so far going well, just as the power LED and the Internet now have orange, green had before. Can anything be done about it?
Pixy
15 sleep; 9 disable GPIO; GPIO enable 8; 12 disable GPIO; GPIO enable 14; 11 disable GPIO; GPIO enable 13
This Administration-enter the Commands, then you run commands and lights are green!
@ Cristi
if there is still so much talk about antennas, I paraphrase danut67 to the question about increasing the coverage area and…
Please, Mr. Crsti, maybe you can make us a recommendation for an omnidirectional antenna that "beats" something more than what is in stock.
I think many want a larger range of WiFi signal coverage.
something without huge costs that can you recommend?
It would do a little guide acquisition of such antennas and explain the values that represent such antennas.
you know ora some of us liked the perforation as well as that page called “what can two clever hands do” from an old children's magazine. 🙂
I do not recommend - I installed the firmware on a Bullet M2HP and I managed to put back orininal firmware, and so that they be complemented firmware from DD-WRT is available 24h trial.
Before making you interested in better step forum or wiki?
NO!
Generally man rushes and then regret it.
Measure of 3 times and cut once, I said it in the tutorial!
The DD-WRT is NOT a trial for the router presented in this tutorial and, moreover, not for many other routers! For other types of routers there is NO "revert.bin", to return to the original firmware, with which the manufacturer delivers it, but there are other bypass procedures, much more complex than using a "return" file. such as for the D-Link DIR 600 wireless router! So, if the procedure to return to your original firmware was similar to that of a D-Link DIR 600 and you did not follow it exactly, then we understand why you are complaining!
Therefore, I, ONE, on the contrary, RECOMMEND this firmware - for those who know what I do - I being one who has the model mentioned above - D-Link DIR 600 on which I flashed the DD-WRT instead of the from D-Link! It works even now, without problems, for almost a year. It increases the flexibility / functionality of the router, without costing you anything more than the price paid when buying the router.
Some of the advantages of the DD-WRT firmware:
(I'll start with the most important prerequisite for using DD-WRT)
- WOL (Wake On LAN) - I can turn on ANY computer connected to this router,
Anywhere in the world where an Internet connection exsit;
- you can increase the wireless transmission power;
- you can establish an SSH connection WITH the HELP of your router, so that it
safety of our data interception;
- you can have multiple SSIDs, through the virtual SSID function, so that
each SSID to have her own level of security;
- you can isolate the respective SSIDs between them, without forming a LAN, between them,
someone so connected to one of the many SSIDs can not
Share files look see on other SSIDs;
- with this firmware - DD-WRT - you have the possibility - unlike
firmaware the D-Link as you access the remote (remote access
management) it's configuration menu router via a
encrypted "https", so that any interception of accessing the menu
will not be of any use to anyone;
- there is the possibility of prohibiting the access to the Internet of needles
computers in the LAN, which do not want to give them access to the Internet, and
that the hourly levels if you want;
- you can change NOT ONLY the access password in the router menu-
's, and username, asftel that increases the difficulty of
access router, by other third parties.
I will not lie to lay now and other benefits with this firmware rich routers that are compatible, but are still worth more to inclocuiesti manufacturer firmware with this open source firmware!
Be very careful should benoclezi eyes 100 times and then you update firmware button like that are not made by the manufacturer of the original firmware router are some unsigned firmware which is more in Romanian is an illegal thing to use a custom firmware with firmware a custom to have problems you should have stability router.
Use of manufacturer firmware!
Use OEM Firmware!
Any router and your nulletul's recovery.
Looking for how to do recovery on your routers tftp and make it like new.
Find recovery router with tftp.
As a general procedure is as follows:
1. Set a local ip to the computer
2. TFTP Server firmware start choosing the bullet
3. Hold the reset button 10 seconds then put the power to the router still holding the reset button until the moment when you see that your site TFTP firmware upload on bullet
4. Valid on most routers.
: )
Enjoy.
This tutorial is more than welcome! We look forward to continuing. Given the experience of the undersigned, at the risk of "selling cucumbers to the gardener" I propose to Cristi a setting that I use very frequently, but only on a certain router, namely, LINK-SYS WRT54GL. Somewhere in the wireless settings (Wireless-Advanced Settings-TX Power) there is the possibility to increase the transmission power of the router almost 10 times, increasing the reception area accordingly. Initially from the firmware settings, the power is 25miliwati, but it can be increased to 250miliwati. However, with the increase of the transmission power, the current consumption also increases and at the same time the heat dissipated on the final shortcut of the router's emission amplifier also increases, which could lead to the floor burning by overheating. I use, as I said above, LINK-SYS WRT54GL routers, and the transmission power does not set it more than 200miliwati. Personally, I installed 5 such routers and they run flawlessly with such power, they heat up moderately, but none of them burned. Moreover, I have advised others to use this type of router, precisely because of this possibility of setting and I have not yet received any complaint regarding the burning of any. I would like to add that I replaced the power supplies with which the routers were delivered by the manufacturer with a current flow of 8-300mA, with power supplies of at least 500mA. I don't know if other routers compatible with this type of firmware are able to support the increase of the transmission power. I would be curious to know other opinions on this subject.
I installed DD-WRT v24-sp2 (06 / 14 / 11) on a TL-WR841N. After loading the MAC addresses in the static DHCP I ran net knows to assign DNS and 1 2 and tangle, locks, had to return to dynamic DHCP. E cabbage, stick with the original firmware
Before you start make some comments, read below about the topic it's worth, if you do not.
Begin not read the comments, so no!
Do not try custom firmware I said that! (If necessary)
Do not be quick, be patient a firmware!
Do not put the firmware is not stable, so it is illegal ptr router, router destroy completely the risk!
Remain the original firmware! (Which to be stable!)
You may be right… it may depend on the router model, it remains to be seen.
I have a dlink dir eg 600, I flashuit a year ago with dd wrt and are satisfied with it. I had no problems with DNS, it works and the standard (in my case rds) and those of opendns.com. I made some reservations among local IPs assigned by the router and network card for Macs.
If you had read carefully - if you put in your head what you are supposed to have watched in the tutorial - on the DD-WRT site, in their database, exactly your type of router does not exist! So, what pretensions do you have and how objective do you think you can be, in your case, considering that you had no idea what you were doing, before you started flashing ?! Why would anyone follow you, as long as you completely ignore the whole article, the only thing you still watched, from here was just the title ?! Once again: your router is NOT SUPPORTED BY DD-WRT! The rest is a story!
Please do not comment without documentation. Search for "841" on DD-WRT and you will find 3 types of TL-WR841N routers for versions 3,5 and 7. I took the original installation from here, it had problems, I dug 3 hours on their forum and I took the latest version on their ftp and behaved identically. I will try when I have time to access with PUTTY and make the settings for fixed ip
I flash watch a D-Link DIR-615 with DD-WRT and go f better believe it merita.Setarile are more complex and seemingly placed more intuitive.
From what I read in the comments above I can understand that great power. In my default after flash with DD-WRT uirea power is in milliwatts 71.
How late can raise the amount that is smooth without the risk of fry and also without replacing the PSU with a more powerful stok?
Even if you find the maximum emission power magnification router without changing the feeder, not all can increase the power too much, considering that PC-ul/laptopul that will communicate with that router will not issue as powerful at the same distance to the router was increased, the emission.
Theoretically it seems to be. I have two routers and two furnizorideInternet Links SysWRT54GL, both set to 250miliwati.Pe laptoapele see the two routers in the network with maximum signal without losses due to wireless.Daca I pachete.ele loss is due to ISP. If you watch IP-TV, one of the suppliers only have streaming interruptions. I changed routers between them and the phenomenon remained deunde conclude that the router is not guilty.
My fault, my fault! I discovered what blocked DNS: I skipped a point when entering a static IP in DHCP (deh, glasses ..) The router does not know how to check when entering data and any human error confuses it. Compared to the spartan router from TPLINK, it has a lot of functions and settings that give you total control over it (including the Romanian language interface, QOS with HTB, the possibility to change the transmission power…), everyone can configure their perfect router.
@ Xantes
D-Link DIR-615 has a feeder and 5 1.2V.
It remains to pass the test
Hi, I also have a TP-Link TL-WR1043ND router and after I connect with my laptop to it via wifi less than 30 minutes pass and the connection "dies", the wireless network only exists and I can only connect via cable. It only recovers if I unplug it. I also did a firmware update in the hope that the problem will be fixed, but to no avail. I saw that everyone praised this router and that's why I took it. Maybe I'm more unlucky and I got a bad one. It's been two days and I've had enough problems. I left it on for about 10 hours without any device connected to it and it did not fall, in conclusion when there is traffic then the router "dies". I forgot to mention that I still have a D-Link DIR-615 and with this router I had no such problems. Please help me, any idea is welcome. Thank you!
You see that it is possible to disconnect after a certain period of inactivity on the network. I set to Network-> WAN-> Connect on Demand-> Max Idle Time = 0, so that it does not disconnect from the internet. But if you have problems with it while using the internet, I don't know what the problem might be. Good luck!
Hello Cristi,
I got a Linksys WRT54GL you can look and you on dd-wrt.com and tell me what file should I start for many and they are to be put primu nustiu ..
Hello! I have a net from romtelecom… and I also give a net to 3 other neighbors. Question: can I control the download speed of the neighbors? and the others are barely moving on the net..I mention that I have a wireless router from netgear, or is there something like that, maybe? I apologize dak I didn't express myself correctly ..
Yes, you can limit the speed of one of them if your router is smart enough and has the technology QOS (quality of service) Enter your router and search options / menu QOS
Hello!
WiFi settings, along with the physical interface which we secured (this is the network that personal use) I created a virtual network locked, for friends who want to enter the net occasionally.
The question is how to isolate the two networks connected to the unsecured network could not see Sheru content on networked PCs secure. Tutorial to speak about something, I've changed my settings but not stands.
That promised tutorial with the explanation of the settings would be very welcome.
Thank you!
Hello everybody! I Dlink router-dir300 rev1 and I managed to upgrade the firmware dd-wrt. Still not used to the new interface, I set right now just user / password that. It would be very useful with a videotutorial settings in more detail as you promised Christ. Not the other, but if we have a larger capacity, why not use the most? Really, really good as a sequel to this episode, even my request! How about Cristi, you dare? Waiting!
Hello,
If you have not installed and what settings work to do. N router is not even bear 150mbps or 300mbps. Especially 2317 Atheros chipset is very old. Great speed wireless LAN will not get more than you do any tuning. Get a router with atheros AR7241.
Very interesting tutorialul.Daca can be interesting tutorial about cuum is instalaeaza certain applications these routers with dd-wrt ex media player server, torrent client samba (optware package) or as larger memory router with usb port
I think you're asking too much from a router. For what you ask why they invented NAS's. Routeaza router and that's all, you want more and a Network Attached Storage or PC.
DD-WRT has been optimized for the best possible Internet routing.
Not asking too mult.Tp can wr1043nd my everything I said above I just do not manage to configurez.Cine you know how to switch from the stock OpenWRT firmware please let me know and give me details Thanks!
Goes to show how the stock firmware in the tutorial video! Yes play the video and watch the tutorial head-tail (without rewind).
From the stock OpenWRT do not think, from dd-wrt to stock
Name
Why are you showing me this http://tinypic.com/r/e8tj76/5 when I want to go back to the firmware by default?
If you can do a tutorial how to "resuscitate" a router.
For different cases:
= when a UP with firmware other than the original one was performed - but the power is interrupted - this situation led to the impossibility of connecting to the router with 192.168.1.1 (or as the case may be)
= Faulty installation of an alternative or the original firmware: router can not access 192.168.1.1., Can only connect with the serial port PUTYY
And such examples.
Hi Cristi, in this model (v2.1) how is the processor 400mhz or 350mhz?
Hello! Please help me about a WRT160NL the storage router, which i want to change the firmware (the default to be replaced by DD-WRT). I would be interesting to use this router to an application that knows how to reserve my name (eg.: When I login to the router from the internet to do with the domain name, as the DHCP addresses from RDS, the fixed are very expensive), or to oblige my RDS server allocate the same IP address. I mention that I bought domeniu.ro. Or, if there is any solution to help me about it, they look great interest, and I thank everyone in advance for the answers and help! Sincerely,
Sal, on to your problem is simple. The system used is the dyndns or dyn.com, but you have to pay pro version, in which you can put your domain domeniu.ro there and in DD-WRT just put domeniu.ro username and password, and automatically you will update the IP address from domeniu.ro all the time. Indifierent what ip you. I do not know how much was something between $ 30-40 of last year. in my work.
In short.
1. to install dd-wrt.
2. you sign the http://dyn.com/ Dyn Standard DNS package, $ 29.95,
3. put your account in the router and you have solved the problem.
But can you search on the net similar stuff, or that supports dd-wrt site
Thanks for the suggestions, but I want to avoid any such way, I just do not depend on any booking site name (DNS) and on obtiunea this, install DD-WRT firmware has even default. Thanks, and if you have other ideas, please help me further!!
As long as you have a dynamic IP and want to do what you say, you have such an account than or dns or static IP from provider fee. All that's about
You must enter the DD-WRT website and look carefully to see if your router is compatible with DD-WRT. Otherwise, goodbye router! As dyndns, not necessarily to pay. You can choose a free domain from them that you can set in the router. Install an updater in pc and ready. I think you router (by name) TP-LINK. I have D-Link and I dlinkdns account, about the same as DynDNS.
that can install custom firmware if I can not get into the router?
NO! It's like you want to install Windows without a computer.
router's good just to have a measuring tape firmware to the net and you can enter any ip in it
It makes no sense what you say! If you can not get into it, then how do you set? What brand is it? You do not have the instruction manual? Write up in the address bar or 192.168.0.1 192.168.1.1 Or login to the router via Ethernet cable, short guy. A question about the router is good, then why do you do the firmware upgrade? If we mess is irreversibly gone!
SUPER TUTORIAL!!
I've installed DD-WRT Asus RT-G32 VA, but I can not connect to the internet, if you can continue the tutorial to be made in the router settings. Thank you.
Have you tried the Ethernet cable? You have entered the website of him can set?
Cristi, your router broke down, or did you just not continue with the settings? you just promised 7 XNUMX months have passed
Hi I've got the same router ...
If successfully went tutorial, it can happen to me as
If you follow all the steps exactly a walk. You do it on your own responsibility! But if your router works fine, why?
hello. I put myself on a ddwrt tp link tl-wr841nd and everything is ok until I downloaded utorrent when disconnected from the internet and have to figure restart the router to reconnect otherwise would not under any circumstances. Any idea what the problem is? thanks
It seems common sense and an accurate answer
Hello,
I flashuit WRT54GL of multiple routers from Linksys with this new firmware. Among other settings, we increased and power output. I walked slowly up to the maximum output of the firmware, without any one of them to crack. Precaution, I replaced one of 2 feeder output. I noticed that I forced routers such ultimate power output, not even heat up too much, instead we have satisfied the requirements of clients to have greater range transceiver.
My question is if anyone has tried to enlarge the limits of output power in broadcasting TP-LINK router and to where it was.
All the best,
Strommy
When you make and the tutorial settings? I forget my flash the router but do not know how I set it, please produce a tutorial setting this custom firmware. Thank you.
traffic can see IPs done in real time?
For those who have suffered like me and bought the router in question, the TP-Link TL-WR740N router but has version 4 there is still no possibility to download firmware modification files (or I have not searched enough ) so the tutorial can be used… still. I repeat for those who have version 4… I bought the router last week and it seems that on DD-WRT there are problems regarding the modification of the router firmware with this version (it only appears):
Chipset AR9331 Other downloads
32 MB RAM
FLASH 4 MB
Hi, does anyone have time to show us how to put OpenWrt backfire on a router? I am in wl500w. Thanks in advance!
In this type of router, unfortunately can not be installed:
Firmware Version: Build 3.12.11 110915 Rel.40896n
Hardware Version: WR740N v4 00000000
I have this error even for the original firmware:
Error code: 18005
Upgrade unsuccessfully Because the version of the upgraded file was incorrect. Please check the file name.
Bye. I have a TP-LINK TL-842nd and I wants to upgrade. On dd-wrt firmware is not for him. 1 Question: Is there anywhere else?
Question 2: The TL-wr841nd is compatible or not?
The problem is that the download speed 842nd (torrent) decreases after 20 sec. from over 9MB / s under 2MB / s and a SpeedTest gives me over 80Mbps. If you can give me an answer by email. Thank you!
To further reduce the risk of a failed firmware update (in which case you can throw in most cases your router) I recommend using over porcesului, as extra precaution, connecting the router to a computer and UPS. If you fail in the process stream greeting router. true if this other stuff (bios update, firmware different devices).
The advantages of using custom firmware from dd-wrt are huge and if you have a compatible router it's a shame not to use it. not only does it add new functions but it increases the operating stability of the device and on top of that you can even "overclock" the device to increase its range. (here be very careful not to burn it - high values of power supply will heat it up)
in connection with "throwing in the trash", in the case of the router there is no need to throw it in case of failed firmware!
the new generation routers can move easily to factory firmware!
What is firmware recovery?
Simple, when firmware is buseste, most often after a wrong upgrade / blackout / reset / unplug during upgrade, the equipment can not be used.
The vast majority of old equipment arrived in the trash after such an event.
Current products shows this recovery procedure, which means it still is not dead after all, but we have a chance of resuscitation through a rewrite.
How is it?
First, unplug the product. Press the reset button with a paper clip or pen and hold. While holding down the power to the router… it will be harder to do this with 2 hands but it is not impossible. After powering up, hold down the reset for another 10-15 seconds. That's it, the old firmware, good or bad, has been deleted.
Because we're soft on it, the router will not give the address automatically via DHCP or wireless issue, so we need to set the address manually to a wired network card IP 192.168.0.X class without 1. No need yet to get gateway or DNS.
Now open the browser address 192.168.0.1 and should see a simple page which can not only make the upgrade file upload correctly. After rewriting everything should return to normal. Do not forget to check back plate computer address automatically if you do not want a manual address.
If the 192.168.0.1 Do not show anything, try the procedure again, otherwise it's just thrown in the trash.
The procedure is valid for the return of the DD-WRT software back to D-Link.
Good luck
Salut.Cand will appear and a videotutorial about functions and settings on routers with dd-wrt firmware?
All settings are explained on the website of the dd-wrt, of course in English.
Hi guys! I also have a TP-Link router WR740N, v4.2 hw version and I want to install DD-WRT. I see the website of the DD-WRT firmware is not official but no one called BrainSlayer. Do you think I'll have any problem if I try to Intal that firmware? Esteem
SHAWL
Search http://www.dd-wrt.com
Select
Router Database in da search box write WR740N
Search result 3 review, the last is 4.0
Hi there!
HELLO
I have a Broadcom chipset router Tenda W311R v5.07.15
( http://www.tenda.cn/tendacn/downloads/show.aspx?productid=353 ) I like the defendant in china (AliExpress)
firmware chinese ..
day I did a firmware update (for English) with this firmw. (W311r v5.19.10_en) on the same page.
Now he turns the lights, flashing when you stick cable. yet so does not appear in wifi.
I tried the instructions above (What is firmware recovery?) but nothing.
there any hope of resuscitation? or throw?.
Thank you. AR
I have the same problem
Hi.
Using dd-wrt firmware can monitor duration (hh: mm: ss) for use of a computer in many calc. linked together on a router from a certain day? Found on the net about this firmware only able volume visualization in / out per day, anything related to the duration of navigation.
Thank you.
Hello,
Please, if possible, a tutorial on what settings are required using dd-wrt firmware (as we have promised). Talk about important settings and if possible on other posibile.Asteptam forward this tutorial and thank you for the job they still do.
Hello again.
I got a router in this version 4.23. On site at dd-wrt see that ver. 4.x is supported but not gasibile those files. Bin What do I need? The uinde they take? Can you get those at v. 2?
Thank you.
I have a TP-Link WR 940 routter N.se can install? thank
Hello
I installed dd-wrt on the router Firmwar TP-Link WR740N v4.2
indeed has several functions. including the Romanian language. however a price everyone know to walk with them.
But the biggest drawback that I noticed him (at least in my case).
I connected the laptop to it via wifi:
1) security type: wpa2 Personal, AES encryption type to connect a laptop, connect only with TKIP / AES or TKIP simple.
2) I did the speed test samples. a salt-16 18 mb download speed.
I disconnected wifi, and I connected with lan. 92 93-speed mb. so I returned to the original firmware wr740nv4.
I repeated the tests: one is the type decoding wifi figures.
speed wifi. - 36-40 mb.
lan cable-92 93 mb.
My ISP is RCS-RDS. Chosen speed FIBERLINK2 to 100mb
so my opinion is, if you were bought TP-LINK WR740N (58.04 RON) to the left as it is but the original firmware.
How to make a tp link 1043nd which I installed dd-wrt? It can make a videotutorial.
shawl. question: the following situation arises: a friend of mine qa left behind leaving 2 cameras on ip and a web miniserver (raspberry pi, an automation) on a router… the provider stopped the net from that router on the move as it was looping. the router can be accessed from wifi but I can't physically reach it… it still has an internet connection (another router). how can I bridge between them so that they can be accessed through the other router?
Your answer may be dd wrt, any server + ip tables. thank you very much
And I Salut.Am problem. I have a wireless N Gigabit Router TP-LINK TL-WR1043ND and installed the update firewall gresit.Si mg routerul.Cum not bring him back to life, or delete update? MS
read above! Do you have the "firmware recovery" procedure?
Could you explain to me how to do recovery, the same thing happened to me on the same router.
Hello
no worries, if you started this thing, the next tutorial should have been with setting up the router, don't you think …… ..?
Me, I'd be interested if this router can be configured with multiple SSID after such an operation. RDS connection.
Boas, tenho uma versão Brasileira roteador Desse has versão 4.22.
Roteador Esse é muito bom, a dish 5Dbi porem que vemos ments, é apenas para recepção (RX) antenna der it transmissão (TX) é na imprimido PCB.
Isso phase of roteador by Curto Alcance dele.
Outro dia como eu vi em um site para fazer adaptar TX antenna ments, mas não save a link is drawn porque hoje Corro esses dias para compra um.
I need to set to have the same speed for cable and rds (54 MB) and when I speed bag N router 740 32 MB?
I want to mention that I own a D-Link615 rev H1 router, the idea is I did not want to buy another router that is compatible and ready for IPv6, from what I saw many people use this router that is really stable I did not have problems with it for 2 years since I have it, I have already taken this step and installed this OpenWrt firmware and I want to say that the 2 day router is really stable I had no problems but I failed to make the setting work and IPV6 maybe I missed something so I turn to you if you know about this update… thanks and I'm waiting for an answer !!!
Something IPv6 settings for the router and modem 3G openvrt or DD-WRT?
Hi. I also have a problem. I have a router Wireless router N Gigabit TP-LINK TL-WR1043ND and I installed openwrt update and the router no longer works. In the properties of the network card I see ip of 192.168.1.1, but I can't I access it, it tells me the unavailable page …… Please help me! As I bring it back to life, or delete the update, to write the original one again, it can be seen that openwrt doesn't work !!!!!!!
http://klseet.com/index.php/tl-wr1043nd-ver18/reset-failsafe-revert-to-factory follow the steps here goes Guaranteed
I had the same problem! I was ready to declare him dead three days after entering the address manually, automatically and in every way. Yet not have a router brickuit symptoms of what I saw through tutorials! After watching a tutorial of Crisi (I want to thank him for this way. What do pt. We who are less knowledgeable in the IT) I gave in cmd ipconfig command and noticed that proved 192.168.11.1 address the address was supposed to be inserted 192.168.1.1 not to confuse you so far! Cristi still waiting tutorial with DD-WRT optimal settings! Thank you.
In this tutorial you said it will continue tutorials with DD-WRT. Did you expect them?
He went first to a D-Link 615 ver. Hx. No problem. Ip: 192.168.1.1
https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-frc3/t1/1896971_825052390853931_273380047_n.jpg
Hello, I have a tp link wr740n v4.24, I installed ddwrt, we cloned and macu, I base the dhcp setting automatically goes here really do not know, I have a dynamic ip internet where I wrong to fail to I knew it!
Hello Cristian.
All your tutorials are perfect. Interesting and congratulate you for your efforts.
You promised a continuation of the tutorial with Installing DD WRT on TP Link, a tutorial with DD WRT settings.
I would be very folsitor. Thanks
Howdy,
Can you tell me how I can make a router when someone connects to wireless and open some net page?
Thank you in advance
Hello,
I did this thing with a router tplink901nd. We expanded coverage, I signed, but I have internet (limited conection). I did the same thing (we extended a hotspot semnnalul on iPad) and there I went.
Any idea?
Thank you.
very good tutorial I in 10 min I finished resofting a netgear wndr3400 priml was the basic file .chk then the mini version then the mega version and it works but I still haven't found the tutorial for the bridge router… otherwise everything is ok down with the hat 🙂
and tutorial # 2 about DD WRT functions did not come…