Hi friends, today we will see how we can speed 300 or 150 Mbps (depends on network card) on wireless. Many of you you have purchased laptop or tablet and you have noticed that the wireless speed is not as high as you expect, that even if you are near the router.
Due to the limited speed wireless channel bandwidth is usually router issue 20 / 40 Mhz instead the vast majority of cards are limited to only 20 Mhz.
It must be said that not all wireless NICs can achieve 300 N Mbps, but many can achieve and do not do because of this limitation.
To speed touch with your network card must have a maximum transmission power of the router and network card can be operated in 20 / 40 for wireless B, G and N are very important drivers, you must have the good drivers, preferably on the official website of the manufacturer.
Careful.
N150 wireless NICs can not go to 300, they are limited in the factory and you do not do.
The tutorial is for those who have network card N300 have N300 router and network card still only go up to 150, or for those who NIC N150 and not actually get on the 65-72 DESAT Mbps.
If you do not have a router, but no bloated budget, I recommend two routers that I have, are quite good and not expensive at all.
TP-LINK TL-WR740N a wireless router super cheap and super good
Netis, a router and repeater capable, small and very cheap
View Comments (86)
Cristi I want to do the same thing yes no onboard wireless network and the Ethernet integrated in Speed appears to me 100 Mbps while the network card is Gigabit, in settings there in taboo Advance does not have bandwidth capability and no other setting I set that allows me this. You may have to take their own speed according to the speed router? Gigabyte motherboard GA-B85-HD3 rev2.0
In vain have gigabit network card if your router is not gigabit and gigabit packet does not have the Internet provider
The router is the presenter crystal tutorialu Netis few days ago and can go up to 300 Mbit and I wish my board network and even to go to the Mbit 300 as if to say, so I kind of have a network NAS I do stand to transfer even with 100 300 Mbit?
Indeed router can go up to 300, but wireless. The wire goes only up to 100.
Indeed, the router goes to 300, but wireless. The thread just goes to 100
Mr. Cristi I bought this router [ http://www.emag.ro/router-cu-doua-benzi-n600-wireless-2-x-300mbps-wf-2471-retw0066/pd/DSLQCBBBM/ ] and I would like to know what coverage I have in Madrid and I would like to connect to the neighbor's [parents' router [The problem is that it is about 100,200 meters from me a block as an obstacle I bought this router in the hope that but I can connect but my question is. what could i do to connect to that router Thanks
Thank you!
I "grew" with Toshiba encore from 130Mb / s to 270Mb / s !!!
Something similar settings pt.Android?
Unfortunately, Android does not have such advanced settings. However, I will do some digging, maybe who knows ....
That is classic Android does not have one but CyanogenMod has more advanced wireless settings. Proof here https://db.tt/1spRqZF7
This setting is classic and Android.
I am referring to advanced network card settings. Gen Windows "Configure ..."
Probably somewhere a file conf, but you have to find it and have it slaughtered.
Hello Cristi have a rooter from Huawei B662 orange and speed is mb ii 54 can increase the speed?
Maximum speed Mbps Wireless G is 54. This speed can be increased.
Sal, I own a wireless router TP-LINK TL-WR 841N and box shows me 300MB and in connection shows me just 72 MB. What settings to get them to reach and to me even at 250 MB. Thank you and I wish you the best day possible.
Do you follow the tutorial?
Set the router channel width on 40 Mhz frequency. See here: http://www.tp-link.ro/resources/simulator/TL-WR841ND_v9/Index.htm.
So the router is to achieve maximum transfer rate 300 mb / s Your receiver wifi traffic reaches a maximum 150 mb / s if working on 20 Mhz, if you can work on 40 Mhz (ie 20 20 + Mhz, dual band, as seen in this tutorial) then traffic can be perceived 150 than mb / s
You realize just 72 mb / s for your router has made setting I mentioned above and it emits only 20 MHz default frequency, so will not be able to achieve a higher transfer rate 150 mb / s and you receiver somewhere in half for wifi so can your handset.
Yes, I watched but you have a different router from mine and I have not found me Bandwitch Capability. Do not ask if I had not watched videotutorialul. So what remains? You wanna tell me to my router settings how do I do? Thanks.
Bre, I did not do the router settings, I changed a setting in the network card. It is assumed that the router is set well and deliver the 300 Mbps.
If you want to make a tutorial on advanced settings of a router, ask in the comments box.
Antenţie, as I said-n and-n tutorial text, not all network cards can go up to 300Mbps if N150 can go maximum to 150Mbps.
If N150 not approaching this speed, you can make this setting. If you have not set it means that your network card does not allow you to make changes too advanced.
There are more advanced NICs and NICs simpler.
The driver also plays a very important role.
I have the same problem with a Presario CQ56 laptop with Windows 7 x64 rom. and I don't have that setting in the properties! If you could help me too ... I have a net from Upc with their wireless and I have a speed of 72 right next to the router.
if you're happy 72 REAL mb
Make beautiful tutorials, interesting. But I noticed that you kinda stopped with tutorials for software and web services like email, web hosting sites. Than hardware and on mobile.
There are more visitors interested in hardware and Android than hosting and managing a domain / site / blog etc.
If I had several requests on the comment field, I definitely return with such topics.
We also work with the client's material ...
It would be interesting some tutorials on servers / hosting / networking or IP cameras
Yeah right, you're right. It would be nice to see and tutorials on software, internet, email, websites, etc. as before.
Anyway remain the strongest in terms of video tutorials, guides and tips.
Cristi can you please reply to me thanks to the question above.
every connection has a name
if you know the name of the connection to the router in question, and if the PC sees that connection, and definitely you know
and password then you can connect to that router SIMPLE as hello :)